allPIXA evo 16k CXP

allPIXA evo 16k CXP

Article summary

Did you find this summary helpful?

Thank you for your feedback

Camera specifications

Sensor	CMOS line scan sensor
Pixel size	5 µm × 5 µm
Line spacing	5 µm between R-G & G-B
Spectral sensitivity
Resolution	16384 x 4 lines
Video output	4 × CoaXPress 2.0
Data format	3 × 8/10/12 Bit color or 1 × 8/10/12 Bit mono or
Trigger Mode	Frame Start / Frame Active / Line Start External trigger Line trigger / Encoder and Frame trigger
Video output port	4 × CXP-12 Micro-BNC
Interface position	Y, Z
Digital I/O port	External I/O (15 pin HD D-Sub, fem.)
Power supply	6 pin Hirose, male 12 V – 24 V DC ± 20 %; 1 A @ 24 V
Debugging port	USB 2.0 (Micro USB)
Lens mount / adapter	M95 × 1 mm
Housing dimensions	102 mm x 113 mm x 102 mm (W x H x D)
Weight
Temperature during operation	0 °C – 60 °C; 32 °F – 140 °F
Humidity during operation	20 % – 85 % relative air humidity, non condensing
Temperature during transport and storage	-20 °C – +85 °C; -4 °F – +185 °F
Protection category	IP50
Certifications	CE, RoHS
General ambient conditions
Transport	IEC 721-3-3:IE33
Operation	IEC 721-3-3:IE21
Storage	IEC 721-3-3:IE11

Sensor pixel arrangement

Measured relative sensitivity of the color and the mono sensor

Download as pdf-file
Dimensional drawing of the allPIXA evo 16k CXP – interface position Z


1	Connector for additional fan	2	Video output (4 × CoaXPress 2.0)
3	Power supply	4	Status LED
5	Debugging port	6	Digital I/O port
7	CXP Interface LED

The following connector is required for the power supply cable:

	Pin	Description
Pin allocation of the power supply port	1	Power +24 V
	2	Power +24 V
	3	Not connected
	4	Not connected
	5	Ground
	6	Ground

NOTE

Ensure a proper GND connection of the digital camera I/O port and your trigger.

The following connector is required for the digital I/O port:

evo-digital io_02 Pin allocation D-Sub connector (female) of the camera

Pin	GenICam	Signal	Level	In/Out	Example/Remark
1	Line 1	Enc0_InP (+)	RS 422	Differential input	Encoder0 or LineTrigger
2	Line 2	Enc1_InP (+)	RS 422	Differential input	Encoder1 or Frametrigger
3	Line 3	IO_0P	LVCMOS	Input	single-ended
4	-	RT	RS 485	-	-
5	Line 5	IO_2P	LVCMOS	Out	LED-Out1
6	Line 1	Enc0_InN (-)	RS 422	Differential input	Encoder0
7	Line 2	Enc1_InN (-)	RS 422	Differential input	Encoder1
8	Line 4	IO_1N	LVCMOS	Input single-ended	Trigger or Master-Slave Cascaded
9	-	RTN	RS 485	Out	To LightController XLC4
10	Line 6	IO_3	LVCMOS	Out	LED-Out2
11	-	GND	-	GND	-
12	Line 7	IO_4_SDA	LVCMOS	Out	LED-Out3
13	-	GND	GND	-	-
14	Line 9	Master/Slave	LVCMOS	Bi-directional	Master/Slave
15	Line 8	IO_5_SCL	LVCMOS	Out	LED-Out4

I/O standard	V_IL		V_IH		V_OL	V_OH
	V_min	V_max	V_min	V_max	V_max	V_min
LVCMOS	–0.5	0.7	1.7	3.6	0.4	2.1
RS422	–6	0.8	2	6	-	-

	NOTICE
	Non compliance may cause irreparable damages to the device.
	The maximum input level of the LVCMOS is 3.6 V. Use a level converter if necessary (e.g. 74 LVC14).

The Micro-USB connection is currently used for debugging information.

Color code	Behaviour	Description
	Off	No power supply or the input voltage is out of range.
	Solid orange	The system is booting.
	Flash_1_1red	The device is powered but not connected (not applicable to a device reliant on PoCXP power).
	AlternateFlash_12_5 green/orange; shown for a minimum of 1s even if connection detection is faster	The Connection detection is in progress, PoCXP is active.
	Flash_12_5 orange; shown for a minimum of 1s even if connection detection is faster	The Connection detection is in progress, PoCXP is not in use.
	AlternateFlash_0_5 red/green	The device/host is incompatible, PoCXP is active.
	AlternateFlash_0_5 red/orange	The device/host is incompatible, PoCXP is not in use.
	Solid red	PoCXP is over-current (host only).
	Solid green	The device/host is connected, but no data is transferred.
	Flash_1_ orange	The device/host is connected, waiting for event (e.g. trigger).
	Flash_12_5 green	The device/host is connected, data is being transferred.
	500ms red pulse	Error during data transfer (e.g. CRC error, single-bit error) is detected. In case of multiple errors, there shall be at least two green Flash_12_5 pulses, before the next error is indicated.
	AlternateFlash_0_5 green/orange	A connection test packet is being sent.
	AlternateFlash_0_5 red/green/orange	The compliance test mode is enabled (device only).
	Flash_12_5 red	A system error (e.g. internal error) ocurred.

Color code	Behaviour	Description
	Off	No power supply or the input voltage is out of range.
	Blue continuous	The device is OK and provides image data. Between image gaps the LED is off.
	Green continuous	The device is in power-up mode.
	Green blinking	The device is OK and ready.
	Yellow continuous	Warning-state: The device is operational.
	Red continuous	Error-state: The device is not operational.

Was this article helpful?

Table of contents