Device Error Code

02 Jul 2024
10 Minutes to read

Device Error Code

Updated on 02 Jul 2024
10 Minutes to read

Article summary

Did you find this summary helpful?

Thank you for your feedback

The Device error code is organized in two parts. The upper two bytes define a category The lower two bytes define the specific error that occurred in this category.

Example

If the region of interest exceeds the sensor boundaries, the following error code is provided by the DeviceErrorCode:

0x00010003

The yellow part defines the category and the green part the specific error. Use the category error number to figure out, in which section you need to search for the specific error code.

So 0x0001 is the category code of the image format control (IMF_ERROR_CATEGORY) group.
In this category the code 0x0003 defines the specific error code for the case when the region of interest exceeds the sensor boundaries.

Error Category (Upper 2 bytes)

This section contains an overview of the categories error codes. This is the upper part of the DeviceErrorCode.

Definition	Value	Description
IMF_ERROR_CATEGORY	0x0001	Image format control error category
ALG_CTRL_ERROR_CATEGORY	0x0002	Analog control error category
ACQ_CTRL_ERROR_CATEGORY	0x0003	Acquisition control error category
DIG_IO_CTRL_ERROR_CATEGORY	0x0004	Digital I/O control error category
ENC_CTRL_ERROR_CATEGORY	0x0005	Encoder control error category
USER_SET_CTRL_ERROR_CATEGORY	0x0006	User set control error category
ICC_ERROR_CATEGORY	0x0007	Image calibration control error category
LUT_CTRL_ERROR_CATEGORY	0x0008	Look-up table control error category
CT_CTRL_ERROR_CATEGORY	0x0009	Color transformation control error category.
DEV_CTRL_ERROR_CATEGORY	0x000A	Device control error category
FAC_ERROR_CATEGORY	0x000B	File access control error category
LED_FLASH_CTRL_ERROR_CATEGORY	0x000C	Led flash control error category
IO_ANALYZER_ERROR_CATEGORY	0x000D	IO Analyzer error category

Specific Error (Lower 2 bytes)

This section contains the specific error codes (lower part of the DeviceErrorCode) grouped by the category. Check the DeviceErrorMessage feature to get a description of the error occurred.

Image Format Control (IMF_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the IMF_ERROR_CATEGORY (0x0001).

Definition	Value	Description
IMF_ERR_ROI_INVALID_ WIDTH_OFFSET_MODULO	0x0001	The width or the offset is not a multiple of 8(RGB) or 24(Mono)
IMF_ERR_ROI_WIDTH_ TOO_SMALL	0x0002	The region width is too small
IMF_ERR_ROI_EXCEEDS_ SENSOR_BOUDARIES	0x0003	The region of interest exceeds the sensor boundaries. You need to use a smaller ffset or width.
IMF_ERR_WREF_IN_ MULTIPLE_ROIS	0x0004	The complete gain control region is located in multiple regions. You need to use the gain control region only in one region
IMF_ERR_BV_MAX_ LINE_WIDTH_EXCEEDED	0x0005	The sum of all active region widths and gain control region width (if not completely in one region) exceeds an internal limit of 15360
IMF_ERR_FAILED_TO_ SET_ROI_AT_SENSOR	0x0006	An internal error occurred while setting the region parameters
IMF_ERR_FAILED_TO_ SET_ROI_AT_TRANSPORT_LAYER	0x0007	An internal error occurred while setting the region parameters
IMF_ERR_INVALID_ BINNING_PARAMETER	0x0008	The binning parameter is not supported. You need to use either 1 or 2 for binning parameter
IMF_ERR_INVALID_ PIXEL_FORMAT	0x0009	Invalid value for pixel format. You need to use a supported pixel format
IMF_ERR_COULD_NOT_ ADJUST_ROI_WIDTH_TO_PXFMT	0x000A	Could not adjust region width corresponding to pixel format. Increase the region width before changing the pixel format
IMF_ERR_COULD_NOT_ADJUST_ WREF_OFFSET_WIDTH_TO_PXFMT	0x000B	Could not adjust gain control region width or ffset corresponding to pixel format. Increase the gain control region width or ffset before changing the pixel format
IMF_ERR_INVALID_ROI_WIDTH_ OFFSET_MODULO_PXFMT	0x000C	Invalid region width or offsetX
IMF_ERR_ INVALID_WREF_WIDTH_ OFFSET_MODULO_PXFMT	0x000D	Invalid gain control region width or offsetX
IMF_ERR_FAILED_TO_SET_ PIXFMT_AT_SENSOR	0x000E	An internal error occurred while setting the pixel format
IMF_ERR_ FAILED_TO_SET_ PIXFMT_AT_TRANSPORT_LAYER	0x000F	An internal error occurred while setting the pixel format
IMF_ERR_TRIGGER_SLAVE_DELAY_ LINES_OUT_OF_RANGE	0x0010	The trigger or slave delay lines value is out of range
IMF_ERR_IMAGE_HEIGHT_ OUT_OF_RANGE	0x0011	The image height is out of range
IMF_ERR_TRG_SLAVE_DEL_GCTRL_ OFFSET_Y_TOO_SMALL	0x0012	The trigger or slave delay lines value is too small with respect to gain control region offset. The sum of trigger delay lines and gain control region ffset must be atleast 2
IMF_ERR_ TRG_SLAVE_DEL_GCTRL _ OFFSET_Y_TOO_LARGE	0x0013	The trigger or slave delay lines value is too large with respect to gain control region offset. The sum of trigger delay lines and gain control region ffset must be less than 32767
IMF_ERR_TESTPATTERN_ VALUE_OUT_OF_RANGE	0x0014	The test pattern value is out of range
IMF_ERR_INVALID_PARAMETER	0x0015	Invalid Parameter
IMF_ERR_DECIMATION_HOR_OUT_OF_RANGE	0x0016	The Decimation Horizontal Float value is out of range!
IMF_ERR_INVALID_PIXEL_COLOR_FILTER	0x0017	Invalid pixel color filter!

Analog Control (ALG_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the ALG_CTRL_ERROR_CATEGORY (0x0002).

Definition	Value	Description
ALG_CTRL_ERR_GAINCTRL_ OFFSET_Y_RANGE	0x0001	The gain control region ffset is out of range
ALG_CTRL_ERR_GAINCTRL_ WIDTH_RANGE	0x0002	The gain control region width is out of range
ALG_CTRL_ERR_GAINCTRL_ HEIGHT_RANGE	0x0003	The gain control region height is out of range
ALG_CTRL_ERR_GAINCTRL_ EXCEEDS_SENSOR_BOUNDARIES	0x0004	The gain control region exceeds the sensor boundaries. You need to use a smaller ffset or width
ALG_CTRL_ERR_GAINCTRL_ OFFSET_X_RANGE	0x0005	The gain control region ffset is out of range
ALG_CTRL_ERR_GAINCTRL_ INVALID_WIDTH_OFFSET_MODULO	0x0006	The width or the offset is not a multiple of 8(RGB) or 24(Mono)
ALG_CTRL_ERR_GAINCTRL_ EXCEEDS_BV_WIDTH_LIMIT	0x0007	The sum of all active region widths and gain control region width (if not completely in one region) exceeds an internal limit of 15360
ALG_CTRL_ERR_GAINCTRL_ IN_MULTIPLE_ROIS	0x0008	The complete gain control region is located in multiple regions. You need to use the gain control region only in one region
ALG_CTRL_ERR_FAILED_TO_ SET_GAINCTRL_AT_SENSOR	0x0009	An internal error occurred while setting the gain control region parameters
ALG_CTRL_ERR_STOP_GAIN_ FACTOR_OUT_OF_RANGE	0x000A	The stop gain factor is out of range
ALG_CTRL_ERR_GAINCTRL_ OFFSET_Y_TOO_SMALL	0x000B	The gain control region ffset is too small! It must be larger than 2 when using no frame trigger. When using frame trigger the sum of trigger delay lines and gain control region ffset must be atleast 2.
ALG_CTRL_ERR_GAINCTRL_ OFFSET_Y_TOO_LARGE	0x000C	The gain control region ffset is too large! It must be less than or equals to: Height – GainControlRegionHeight when using no frame trigger. When using frame trigger the sum of trigger delay lines and gain control region ffset must be less than 32767.
ALG_CTRL_ERR_GAINCTRL_ TARGET_VALUE_OUT_OF_RANGE	0x000D	The gain control target value is out of range
ALG_CTRL_ERR_BRIGHTNESS_ CONTRAST_GAIN_OUT_OF_RANGE	0x000E	The contrast (gain) value of the brightness contrast feature is out of range
ALG_CTRL_ERR_ BRIGHTNESS_ CONTRAST_OFFSET_OUT_OF_RANGE	0x000F	The brightness (offset) value of the brightness contrast feature is out of range
ALG_CTRL_ERR_GAIN_ VALUE_OUT_OF_RANGE	0x0010	The gain value is out of range
ALG_CTRL_ERR_GAIN_ AUTO_AVG_SAMPLES_OUT_OF_RANGE	0x0011	The average samples value is out of range
ALG_CTRL_ERR_GAMMA_ VALUE_OUT_OF_RANGE	0x0012	The gamma value is out of range
ALG_CTRL_ERR_INVALID_PARAMETER	0x0013	The parameter is invalid!
ALG_CTRL_ERR_SENSOR_SENSITIVITY_VALUE_OUT_OF_RANGE	0x0014	The sensor sensitivity is out of range
ALG_CTRL_TIMEOUT_READING_VIDEOLEVEL	0x0015	Timeout occurred at reading video level
ALG_CTRL_ERROR_ADAPT_TARGETVALUE	0x0016	Error at adapting Target value for GainControlRegion

Acquisition Control (ACQ_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the ACQ_CTRL_ERROR_CATEGORY (0x0003).

Definition	Value	Description
ACQ_CTRL_ERR_FEATURE_ CHANGE_DURING_IMG_ACQ	0x0001	The feature change is not allowed while grabbing
ACQ_CTRL_ERR_TRG_ SELECTOR_INVALID	0x0002	The trigger selector is invalid
ACQ_CTRL_ERR_TRG_SIG_ DETEC_MODE_NOT_AVAILABLE	0x0003	The trigger signal detection mode is invalid for LineStart. You need to use TriggerSignalDetectionMode feature only for Frame trigger
ACQ_CTRL_ERR_LINE_ TRG_SRC_INVALID	0x0004	The selected source for line trigger is invalid
ACQ_CTRL_ERR_TRG_ ACTIV_INVALID	0x0005	The trigger activation value is invalid
ACQ_CTRL_ERR_TRG_ SRC_USED_BY_OTHER_TRIGGER	0x0006	The trigger source is already assigned for another trigger. You need to use different source for LineStart and Frame trigger
ACQ_CTRL_ERR_TRG_ FRAME_START_ACTIV_INVALID	0x0007	The trigger activation is invalid for FrameStart/FrameBurstStart. You can use RisingEdge/FallingEdge for FrameStart/FrameBurstStart
ACQ_CTRL_ERR_TRG_ FRAME_ACTIVE_ACTIV_INVALID	0x0008	The trigger activation is invalid for FrameActive. You can use LevelHigh/LevelLow for FrameActive
ACQ_CTRL_ERR_FRAME_ TRG_SRC_INVALID	0x0009	The selected source for frame trigger is invalid
ACQ_CTRL_ERR_MASTER_ TRG_SRC_INVALID	0x000A	The source (encoder0, Line1, Line2 and InternalLB) for SelectMaster_Input trigger is invalid
ACQ_CTRL_ERR_EXPOSURE_ TIME_TOO_SMALL	0x000B	The exposure time is too small
ACQ_CTRL_ERR_EXPOSURE_ TIME_TOO_LARGE	0x000C	The exposure time is too large
ACQ_CTRL_ERR_LINE_TIME_ TOO_SMALL	0x000D	The line time is too small. It must be at least 1.5us larger than integration time
ACQ_CTRL_ERR_LINE_TIME_ TOO_LARGE	0x000E	The line time is too large
ACQ_CTRL_ERR_LINE_TIME_ TOO_SMALL_RUNTIME	0x000F	The line time is too small, when considering run time parameters
ACQ_CTRL_ERR_OTHER_FRAME_TRG_MODE_ON	0x0010	Selected frame trigger mode cannot be made On because other frame trigger mode is already On
ACQ_CTRL_ERR_TRG_FRAME_END_SRC_INVALID	0x0011	Invalid FrameEnd source
ACQ_CTRL_ERR_DEBOUNCING_ MODE_INVALID	0x0012	Invalid debouncing mode
ACQ_CTRL_ERR_TRIGGER_ DIV_OUT_OF_RANGE	0x0013	The trigger divider value is out of range
ACQ_CTRL_ERR_TRIGGER_ DIV_NOT_AVAILABLE	0x0014	The trigger divider is not available for any frame trigger
ACQ_CTRL_ERR_TRG_ LINE_ACTIV_INVALID	0x0015	The trigger activation value is invalid for LineStart. You can use only RisingEdge for LineStart
ACQ_CTRL_ERR_TRG_ DELAY_LINES_NOT_AVAILABLE	0x0016	The trigger delay lines is invalid for LineStart. You can use trigger delay lines only for any Frame trigger
ACQ_CTRL_ERR_LINE_ START_DISABLE_INVALID	0x0017	Invalid LineStart Disable
ACQ_CTRL_ERR_INVALID_ SELECTOR_TRIGGER_DISABLE	0x0018	The trigger disable is invalid for FrameStart/Active. You can use trigger disable only for LineStart
ACQ_CTRL_ERR_SELECTED_ LINE_IS_OUTPUT	0x0019	The trigger source used is not configured correctly which is the line mode to output. You need to set the selected line mode to input
ACQ_CTRL_ERR_INVALID_ PARAMETER	0x001A	The parameter is invalid!
ACQ_CTRL_ERR_FRAME_RATE_ ENABLE	0x001B	The AcquisitionFrameRateEnable feature can be enabled only if the mode of all frame triggers is set to off!
ACQ_CTRL_ERR_FRAME_RATE_ RANGE	0x001C	The acquisition frame rate value is out of range!
ACQ_CTRL_ERR_FEATURE_ LOCKED	0x001D	The feature is currently locked and cannot be written.
ACQ_CTRL_ERR_TRG_FRAME_ RATE_ENABLE_INVALID	0x001E	Enabling a frame trigger is not permitted if the AcquisitionFrameRateEnable feature is set.
ACQ_CTRL_ERR_MASTER_SLAVE_MODE_INVALID	0x001F	The master slave mode is invalid.
ACQ_CTRL_ERR_MASTER_SLAVE_INTERFACE_INVALID	0x0020	The master slave interface is invalid Or invalid interface with respect to master or slave.
ACQ_CTRL_ERR_MASTER_SLAVE_NOT_CONFIGURED	0x0021	Master slave is not configured properly. Enable any master slave interface.
ACQ_CTRL_ERR_MS_AUTOSELECT_LINE_USED_AS_TRIGGER_SOURCE	0x0022	Enabling AutoSelect mode is not permitted if MS Autoselect line is used as TriggerSource.
ACQ_CTRL_ERR_AUTOSELECT_MODE_ON	0x0023	Enabling the selected trigger is not allowed if trigger source is MS master or slave or autoselect line master slave configuration.
ACQ_CTRL_ERR_TDI_INVALID	0x0024	Invalid time delay integration value.
ACQ_CTRL_TDI_NOT_AVIALABLE	0x0025	TDI feature is not available for color sensor.
ACQ_CTRL_ERR_FRAME_ACTIVE_EXTEND_LINES_IS_OUT_RANGE	0x0026	Frame active extend lines is out of range.
ACQ_CTRL_ERR_EXTEND_LINES_NOT_AVAILABLE	0x0027	Frame Active Extend Lines feature is not available for FrameStart, frameBurstStart and LineStart trigger.
ACQ_CTRL_ERR_ACQ_START_DURING_IMG_CAL	0x0028	Acquisition cannot be started during internal DSNU or PRNU calibration process. Try again later.
ACQ_CTRL_ERR_TL_THROUGHPUT_TOO_LOW	0x0029	Too low transport layer throughput! Change the link configuration for an image acquisition.
ACQ_CTRL_ERR_MS_LINE_USED_AS_TRIGGER_SOURCE	0x002A	Enabling master or slave mode is not permitted if MS master or slave line is used as TriggerSource.
ACQ_CTRL_ERR_MS_MASTER_MODE_ON	0x002B	Enabling the selected trigger is not allowed if trigger source is MS master line of master slave configuration.
ACQ_CTRL_ERR_LED_FLASH_ON	0x002C	Enabling the selected trigger is not allowed if trigger source is flash out line during led flash is active
ACQ_CTRL_ERR_TL_ACQUISITION_START	0x002D	Error occurred during acuisition start at transport layer! Check the transport layer configuration
ACQ_CTRL_ERR_EXCEEDS_MAX_PAYLOAD_SIZE	0x002E	The calculated payload size exceeds the maximum limit
ACQ_CTRL_ERR_FRAME_END_MODE_ON_NOT_ALLOWED	0x002F	FrameBurstActive trigger must be ON to enable the FrameEnd trigger mode

Digital IO Control (DIG_IO_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the DIG_IO_CTRL_ERROR_CATEGORY (0x0004).

Definition	Value	Description
DIG_IO_CTRL_ERR_LINE_ SELECTOR_INVALID	0x0001	The line selector is invalid
DIG_IO_CTRL_ERR_ USEROUTPUT_SELECTOR_INVALID	0x0002	The user output selector is invalid
DIG_IO_CTRL_ERR_ LINE_INVALID_MODE	0x0003	The line mode is invalid with respect to the line format.
DIG_IO_CTRL_ERR_INVALID_LINE_MODE_ SOURCE	0x0004	The selected line mode is not valid with respect to the line source. You need to use the selected line mode to output or line source to off
DIG_IO_CTRL_ERR_ LINE_MODE_SRC_CHANGE_NOT_ALLOWED	0x0005	The selected line mode or source change is not allowed. The selected line is used either as a trigger source or as an encoder source or MS mode is on
DIG_IO_CTRL_ERR_LINE_INVERTER_ NOT_SUPPORTED	0x0006	The selected line does not support enabling or disabling line inverter
DIG_IO_CTRL_ERR_INVALID_LINE_SOURCE	0x0007	Invalid line source
DIG_IO_CTRL_ERR_LINE_SOURCE_ NOT_AVAILABLE	0x0008	The line source is not available for the selected line
DIG_IO_CTRL_ERR_LINE_MODE_ SOURCE_INVALID	0x0009	The selected line cannot be used as trigger source or Master/slave mode. You need to configure the line mode to Input and line source to Off.
DIG_IO_CTRL_ERR_LINE_FORMAT_INVALID	0x000A	Invalid line format.

Encoder Control (ENC_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the ENC_CTRL_ERROR_CATEGORY (0x0005).

Definition	Value	Description
ENC_CTRL_ERR_ENC_ SELECTOR_INVALID	0x0001	The encoder selector is invalid
ENC_CTRL_ERR_SRC_ A_INVALID	0x0002	The encoder source A is invalid
ENC_CTRL_ERR_SRC_ B_INVALID	0x0003	The encoder source B is invalid
ENC_CTRL_ERR_ENC_ MODE_INVALID	0x0004	The encoder mode is invalid
ENC_CTRL_ERR_ENC_ AVG_INC_OUT_OF_RANGE	0x0005	The encoder average is out of range
ENC_CTRL_ERR_OUT_ MODE_INVALID	0x0006	The encoder output mode is invalid
ENC_CTRL_ERR_SRC_ IN_USE_BY_OTHER_INPUT	0x0007	The source is already assigned to other input of the selected encoder. You need to use different source for input A and input B
ENC_CTRL_ERR_ENC_ DIV_OUT_OF_RANGE	0x0008	The encoder divider value is out of range
ENC_CTRL_ERR_ SELECTED_LINE_IS_OUTPUT	0x0009	The encoder source A or B used is not configured correctly. You need to set the selected line mode to input.
ENC_CTRL_ERR_ENC_ SRC_B_INVALID_CONFIG	0x000A	Invalid configuration. You need to set some source for input A
ENC_CTRL_ERR_SRC_IN_ USE_BY_INPUTA_OR_INPUTB	0x000B	The source is already assigned for either encoder source input A or B
ENC_CTRL_ERR_ENCODER_SOURCE_ NOT_CONFIGURED	0x000C	Encoder source is not configured. Set Encoder source input A to any line.

User Set Control (USER_SET_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the USER_SET_CTRL_ERROR_CATEGORY (0x0006).

Definition	Value	Description
USER_SET_CTRL_ERR_ SELECTOR_INVALID	0x0001	Invalid user set selector
USER_SET_CTRL_ERR_ DEFAULT_READ_ONLY	0x0002	The default user set modification is not allowed
USER_SET_CTRL_ERR_ LOAD_USER_SET_FAILED	0x0003	An error occurred while loading the user set
USER_SET_CTRL_ERR_LOAD_ USER_SET_CMD_VAL_INVALID	0x0004	Invalid load user set command value

Image Calibration Control (ICC_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the ICC_ERROR_CATEGORY (0x0007).

Definition	Value	Description
ICC_ERR_LINE_DISTANCE_ OUT_OF_RANGE	0x0001	The line distance is out of range
ICC_IMGCALMODE_ERR_ INVALID_PARAMETER	0x0002	ImageCalibrationMode is out of range
ICC_IMGCALAUTO_ERR_ INVALID_PARAMETER	0x0003	ImageCalibrationAuto is out of range
ICC_IMG_CAL_FEATURES_LOCKED	0x0004	The selected feature is locked due to an image calibration mode is active
ICC_IMGCALPRNU_NODSNULUT_ACTIVE	0x0005	For PRNU calibration a valid and loaded DSNU is needed
ICC_ERR_SCAN_DIR_CHANGE_ NOT_ALLOWED	0x0006	Scan direction is read only when scan direction source is not internal
ICC_ERR_SCAN_DIR_EXT_SRC_ NOT_CONFIGURED	0x0007	The Encoder0 is not configured properly for the use of ScanDirectionSource. You need to configure EncoderSourceA and EncoderSourceB
ICC_CTRL_FFC_ERR_MULTI_ DATASETS_ENABLING_NOT_SUPPORTED	0x0008	Enabling multiple flat field correction data sets is not supported for this mode or device. It is supported only with LED-Flash and some camera variants. See also the feature reference feature availability table.

LUT Control (LUT_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the LUT_CTRL_ERROR_CATEGORY (0x0008).

Definition	Value	Description
LUT_CTRL_ERR_FFC_LUT_ COULD_NOT_LOAD_DATA	0x0001	An error occurred while loading the LUT’s data from flash
LUT_CTRL_ERR_INVALID_ FFC_LUT	0x0002	The LUT does not contain valid data according to the pixel format
LUT_CTRL_ERR_INVALID_ PARAMETER	0x0003	The parameter is invalid!
LUT_CTRL_ERR_IMGCALAUTO_TIMEOUT	0x0004	Timeout at Internal ImageCalibration
LUT_CTRL_ERR_IMGCALAUTO_INTERNALERROR	0x0005	Error at Internal ImageCalibration

Color Transformation Control (CT_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the CT_CTRL_ERROR_CATEGORY (0x0009).

Definition	Value	Description
CT_CTRL_ERR_SELECTOR_INVALID	0x0001	Invalid color transformation module selector.
CT_CTRL_VALUE_SELECTOR_INVALID	0x0002	Invalid color transformation value (gain or offset) selector.
CT_CTRL_ERR_ENABLING_NOT_ALLOWED	0x0003	Already other color transformation module is active.
CT_CTRL_ERR_GAIN_OUT_OF_RANGE	0x0004	Color transformation module gain value is out of range.
CT_CTRL_ERR_OFFSET_OUT_OF_RANGE	0x0005	Color transformation module offset value is out of range.
CT_CTRL_ERR_MODIFICATION_NOT_ALLOWED	0x0006
CT_CTRL_ERR_PIXELFORMAT_INVALID_WRT_SRGB	0x0007	Invalid pixel format to activate sRGB. Set the pixel format to RGB8

Device Control (DEV_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the DEV_CTRL_ERROR_CATEGORY (0x000A).

Definition

Value

Description

DEV_CTRL_ERROR_COULD_

NOT_GET _TEMPERATURE

0x0001

An internal error occurred while getting the temperature

DEV_CTRL_ERROR_INVALID_VALUE

0x0002

Invalid value set.

File Access Control (FAC_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the FAC_ERROR_CATEGORY (0x000B).

Definition	Value	Description
FAC_ERROR_FILE_ALREADY_OPEN	0x0001	A file is already open
FAC_ERROR_INVALID_FILE_SELECTOR	0x0002	Invalid file selector
FAC_ERROR_INVALID_FILE_OPERATION_SELECTOR	0x0003	Invalid file operation selector
FAC_ERROR_INVALID_FILE_OPERATION_EXEC_VAL	0x0004	Invalid file operation execute command value
FAC_ERROR_FILE_OPERATION_IN_PROGRESS	0x0005	File operation is in progress
FAC_ERROR_NO_FILE_OPEN	0x0006	No file is open
FAC_ERROR_FILE_NOT_OPEN_OR_INVALID_OPEN_MODE	0x0007	Either file is not open or file open mode is not write operation
FAC_ERROR_NO_FILE_SELECTED	0x0008	No file is selected. Select any one file
FAC_ERROR_INVALID_FILE_CONTENT	0x0009	Invalid file content
FAC_ERROR_CHECKSUM_CALCULATION_FAILED	0x000A	Calculation of file checksum failed
FAC_ERROR_CHECKSUM_ERROR	0x000B	Comparison of calculated checksum is not matching with the given checksum
FAC_ERROR_INVALID_OPEN_MODE	0x000C	File open mode is not according to the set operation (read, write)
FAC_ERROR_EXCESS_FILE_SIZE	0x000D	File access (read, write) exceeds the file size(max size for writing)
FAC_ERROR_EXCESS_FILE_ACCESS_BUFFER_SIZE	0x000E	File read access exceeds the file access buffer size
FAC_ERROR_COPY_DATA_TO_FILE_ACCESS_BUF_FAILED	0x000F	An error occurred while copying data to the file access buffer
FAC_ERROR_INVALID_FILE_ACCESS_OFFSET	0x0010	Invalid file access offset
FAC_ERROR_FLASH_ACCESS_ERROR	0x0011	An error occurred during flash access like erase, write
FAC_ERROR_INVALID_OPEN_MODE_SELECTOR	0x0012	Invalid file open mode selector
FAC_ERROR_FILE_ACCESS_BUFFER_OVERRUN	0x0013	File access buffer overrun
FAC_ERROR_CLOSE	0x0014	Error during file close operation. The file has not been updated. The file might be invalid.
FAC_ERROR_CLOSE_FATAL	0x0015	Fatal error during file close operation. Avoid switching off camera! Redo the update! Otherwise, the camera might refuse to boot or problems while connecting might occur.

Led Flash Control (LED_FLASH_CTRL_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the LED_FLASH_CTRL_ERROR_CATEGORY (0x000C).

Definition	Value	Description
LED_FLASH_CTRL_ERR_NO_OF_PATTERN_INVALID	0x0001	Number of pattern value is invalid
LED_FLASH_CTRL_ERR_PATTERN_SELECTOR_INVALID	0x0002	Invalid pattern selector
LED_FLASH_CTRL_ERR_INVALID_FRAME_CONTROL	0x0003	Frame control is invalid
LED_FLASH_CTRL_ERR_SEQUENCE_TIME_INVALID	0x0004	Sequence time is less than the sum of all active pattern on time
LED_FLASH_CTRL_ERR_FLASH_OUT_ON_TIME_INVALID	0x0005	Flash out on time of the selected pattern is invalid
LED_FLASH_CTRL_ERR_FLASH_OUT_OFF_DELAY_INVALID	0x0006	Flash out off delay of the selected pattern is invalid
LED_FLASH_CTRL_ERR_MULTI_PRNU_FLASHING_ DISABLE_INVALID	0x0007	Disabling led flashing is not permitted if the multiple PRNU data sets are active.

IO Analyzer (IO_ANALYZER_ERROR_CATEGORY)

The below table contains the details of specific error belongs to the IO_ANALYZER_ERROR_CATEGORY (0x000D).

Definition	Value	Description
IO_ANALYZER_ERR_ TRIGGER_ACTIVATION_INVALID	0x0001	The trigger activation is invalid
IO_ANALYZER_ERR_ SOURCE_CHA_INVALID	0x0002	Invalid source channel A
IO_ANALYZER_ERR_ TRIG_POSITION_OUT_OF_RANGE	0x0003	The trigger position is out of range
IO_ANALYZER_ERR_ INVALID_SRC_CH_CONFIG	0x0004	Invalid source channel configuration. Either use both source channel or only channel A
IO_ANALYZER_ERR_ SOURCE_CHB_INVALID	0x0005	Invalid source channel B
IO_ANALYZER_ERR_SAMPLE_ RATE_REDUCTION_INVALID	0x0006	Invalid sample rate reduction

Was this article helpful?

What's Next

Device Status Code

Table of contents

Error Category (Upper 2 bytes)
Specific Error (Lower 2 bytes)